SLASE59F October   2015  – December 2019 MSP430FR2433

PRODUCTION DATA.  

1. 1Device Overview
   1. 1.1 Features
   2. 1.2 Applications
   3. 1.3 Description
   4. 1.4 Functional Block Diagram
2. 2Revision History
3. 3Device Comparison
   1. 3.1 Related Products
4. 4Terminal Configuration and Functions
   1. 4.1 Pin Diagram
   2. 4.2 Pin Attributes
   3. 4.3 Signal Descriptions
   4. 4.4 Pin Multiplexing
   5. 4.5 Buffer Types
   6. 4.6 Connection of Unused Pins
5. 5Specifications
   1. 5.1       Absolute Maximum Ratings
   2. 5.2       ESD Ratings
   3. 5.3       Recommended Operating Conditions
   4. 5.4       Active Mode Supply Current Into VCC Excluding External Current
   5. 5.5       Active Mode Supply Current Per MHz
   6. 5.6       Low-Power Mode LPM0 Supply Currents Into VCC Excluding External Current
   7. 5.7       Low-Power Mode (LPM3 and LPM4) Supply Currents (Into VCC) Excluding External Current
   8. 5.8       Low-Power Mode LPMx.5 Supply Currents (Into VCC) Excluding External Current
   9. 5.9       Typical Characteristics - Low-Power Mode Supply Currents
   10. Table 5-1 Typical Characteristics – Current Consumption Per Module
   11. 5.10      Thermal Resistance Characteristics
   12. 5.11      Timing and Switching Characteristics
       1. 5.11.1  Power Supply Sequencing
          1. Table 5-2 PMM, SVS and BOR
       2. 5.11.2  Reset Timing
          1. Table 5-3 Wake-up Times From Low-Power Modes and Reset
       3. 5.11.3  Clock Specifications
          1. Table 5-4 XT1 Crystal Oscillator (Low Frequency)
          2. Table 5-5 DCO FLL, Frequency
          3. Table 5-6 DCO Frequency
          4. Table 5-7 REFO
          5. Table 5-8 Internal Very-Low-Power Low-Frequency Oscillator (VLO)
          6. Table 5-9 Module Oscillator (MODOSC)
       4. 5.11.4  Digital I/Os
          1. Table 5-10 Digital Inputs
          2. Table 5-11 Digital Outputs
          3. 5.11.4.1   Typical Characteristics – Outputs at 3 V and 2 V
       5. 5.11.5  VREF+ Built-in Reference
          1. Table 5-12 VREF+
       6. 5.11.6  Timer_A
          1. Table 5-13 Timer_A
       7. 5.11.7  eUSCI
          1. Table 5-14 eUSCI (UART Mode) Clock Frequency
          2. Table 5-15 eUSCI (UART Mode)
          3. Table 5-16 eUSCI (SPI Master Mode) Clock Frequency
          4. Table 5-17 eUSCI (SPI Master Mode)
          5. Table 5-18 eUSCI (SPI Slave Mode)
          6. Table 5-19 eUSCI (I2C Mode)
       8. 5.11.8  ADC
          1. Table 5-20 ADC, Power Supply and Input Range Conditions
          2. Table 5-21 ADC, 10-Bit Timing Parameters
          3. Table 5-22 ADC, 10-Bit Linearity Parameters
       9. 5.11.9  FRAM
          1. Table 5-23 FRAM
       10. 5.11.10 Debug and Emulation
           1. Table 5-24 JTAG, Spy-Bi-Wire Interface
           2. Table 5-25 JTAG, 4-Wire Interface
6. 6Detailed Description
   1. 6.1  Overview
   2. 6.2  CPU
   3. 6.3  Operating Modes
   4. 6.4  Interrupt Vector Addresses
   5. 6.5  Bootloader (BSL)
   6. 6.6  JTAG Standard Interface
   7. 6.7  Spy-Bi-Wire Interface (SBW)
   8. 6.8  FRAM
   9. 6.9  Memory Protection
   10. 6.10 Peripherals
       1. 6.10.1  Power-Management Module (PMM)
       2. 6.10.2  Clock System (CS) and Clock Distribution
       3. 6.10.3  General-Purpose Input/Output Port (I/O)
       4. 6.10.4  Watchdog Timer (WDT)
       5. 6.10.5  System (SYS) Module
       6. 6.10.6  Cyclic Redundancy Check (CRC)
       7. 6.10.7  Enhanced Universal Serial Communication Interface (eUSCI_A0, eUSCI_B0)
       8. 6.10.8  Timers (Timer0_A3, Timer1_A3, Timer2_A2 and Timer3_A2)
       9. 6.10.9  Hardware Multiplier (MPY)
       10. 6.10.10 Backup Memory (BAKMEM)
       11. 6.10.11 Real-Time Clock (RTC)
       12. 6.10.12 10-Bit Analog-to-Digital Converter (ADC)
       13. 6.10.13 Embedded Emulation Module (EEM)
   11. 6.11 Input/Output Diagrams
       1. 6.11.1 Port P1 Input/Output With Schmitt Trigger
       2. 6.11.2 Port P2 (P2.0 to P2.2) Input/Output With Schmitt Trigger
       3. 6.11.3 Port P2 (P2.3 to P2.7) Input/Output With Schmitt Trigger
       4. 6.11.4 Port P3 (P3.0 to P3.2) Input/Output With Schmitt Trigger
   12. 6.12 Device Descriptors
   13. 6.13 Memory
       1. 6.13.1 Memory Organization
       2. 6.13.2 Peripheral File Map
   14. 6.14 Identification
       1. 6.14.1 Revision Identification
       2. 6.14.2 Device Identification
       3. 6.14.3 JTAG Identification
7. 7Applications, Implementation, and Layout
   1. 7.1 Device Connection and Layout Fundamentals
      1. 7.1.1 Power Supply Decoupling and Bulk Capacitors
      2. 7.1.2 External Oscillator
      3. 7.1.3 JTAG
      4. 7.1.4 Reset
      5. 7.1.5 Unused Pins
      6. 7.1.6 General Layout Recommendations
      7. 7.1.7 Do's and Don'ts
   2. 7.2 Peripheral- and Interface-Specific Design Information
      1. 7.2.1 ADC Peripheral
         1. 7.2.1.1 Partial Schematic
         2. 7.2.1.2 Design Requirements
         3. 7.2.1.3 Layout Guidelines
8. 8Device and Documentation Support
   1. 8.1 Getting Started and Next Steps
   2. 8.2 Device Nomenclature
   3. 8.3 Tools and Software
   4. 8.4 Documentation Support
   5. 8.5 Community Resources
   6. 8.6 Trademarks
   7. 8.7 Electrostatic Discharge Caution
   8. 8.8 Export Control Notice
   9. 8.9 Glossary
9. 9Mechanical, Packaging, and Orderable Information