Certification
TLIN1124AEVM-DOC-CERT — RoHS Certification for TLIN1124AEVM
RoHS Certification for TLIN1124AEVM
TLIN1124A-Q1
- AEC-Q100 Qualified for automotive applications
- Compliant to LIN2.0, LIN2.1, LIN2.2, LIN2.2A and ISO 17987–4 electrical physical layer (EPL) specification
- Compliant to SAE J2602-1 LIN Network for vehicle applications
- Functional Safety-Capable
- Wide input operational voltage range
- VSUP range from 5V to 28V
- LIN transmit data rate up to 20kbps
- LIN receive data rate up to 100kbps
- Operating modes: Normal, Standby and Sleep
- Low-power mode wake-up support with source recognition
- Remote wake-up over the LIN bus
- Local wake-up via SLP
- 4 LIN channels in one package with Integrated diode and commander pull-up resistor (±6% tolerant pull-up in normal mode)
- Tighter responder pull-up (27k to 48k) integrated for all 4 LIN channels
- INHN pin to control external power regulator
- 2.97V to 5.5V Vio logic interface support
- Power-up/down glitch-free operation on LIN bus and RXD output
- Protection features:
- Bus-Fault Protection ±40V
- Under voltage protection on VSUP and VIO
- TXD dominant time out protection to prevent the faulty channel from occupying bus for extended duration
- LIN dominant timeout protection to prevent excess on-chip power dissipation
- Thermal shutdown protection
- Unpowered node or ground disconnection fail-safe at system level.
- Junction temperatures from -40°C to 150°C
- 3.5mm × 5.5mm QFN package with improved automated optical inspection (AOI) capability
The TLIN1124A-Q1 device is a quad Local Interconnect Network (LIN) physical layer transceiver with integrated commander and responder termination, inhibit, wake-up and protection features, complaint to LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, ISO/DIS 17987-4 and SAE J2602-1 standards.
LIN is a single wire bidirectional bus typically used for low speed in-vehicle networks using data rates up to 20kbps. The LIN receiver supports data rates up to 100kbps for in-line programming.
The TLIN1124A-Q1device supports 12V battery applications with wider operating voltage (5V to 28V) and extended LIN bus-fault (±40V) protection. The device converts the LIN protocol data stream on the TXDx input into a LINx bus signal using a current-limited wave-shaping driver which reduces electromagnetic emissions (EME). The receiver converts the data stream to logic level signals that are sent to the microprocessor through the push-pull RXD output pin. Ultra-low current consumption is possible using the sleep mode which allows wake up via LIN bus or SLP pin.
The integrated commander and responder diode and resistor, electrostatic discharge (ESD) protection, and fault protection allow designers to save board space in the system. The device prevents back-feed current through LIN to the supply if the ground shift or supply voltage is disconnected.
Technical documentation
No results found. Please clear your search and try again.
View all 1 | Top documentation | Type | Title | Format options | Date |
|---|---|---|---|---|
| * | Data sheet | TLIN1124A-Q1 Automotive Quad Local Interconnect Network (LIN) Transceiver with Integrated Commander Pull-up Resistor and Inhibit datasheet | PDF | HTML | 24 Mar 2026 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
TLIN1431EVM — TLIN1431-Q1 LIN evaluation module with WAKE, HSS and watchdog
This EVM can be used to evaluate the TLIN1431-Q1 family of devices, including the TLIN14315RGY and the TLIN14313RGY. All IC signals are available on the board, and features of the TLIN1431-Q1 are accessible through the features of the board.
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Simulation tool
TINA-TI — SPICE-based analog simulation program
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
User guide: PDF
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| VQFN (RGY) | 24 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.