Data sheet
CC2520
- APPLICATIONS
- IEEE 802.15.4 systems
- ZigBee® systems
- Industrial monitoring and control
- Home and building automation
- Automatic Meter Reading
- Low-power wireless sensor networks
- Set-top boxes and remote controls
- Consumer electronics
- KEY FEATURES
- State-of-the-art selectivity/co-existence
Adjacent channel rejection: 49 dB
Alternate channel rejection: 54 dB - Excellent link budget (103dB)
400 m Line-of-sight range - Extended temp range (–40 to +125°C)
- Wide supply range: 1.8 V – 3.8 V
- Extensive IEEE 802.15.4 MAC hardware
support to offload the microcontroller - AES-128 security module
- CC2420 interface compatibility mode
- State-of-the-art selectivity/co-existence
- Low Power
- RX (receiving frame, –50 dBm) 18.5 mA
- TX 33.6 mA @ +5 dBm
- TX 25.8 mA @ 0 dBm
- <1µA in power down
- General
- Clock output for single crystal systems
- RoHS compliant 5 × 5 mm QFN28 (RHD) package
- Radio
- IEEE 802.15.4 compliant DSSS baseband
modem with 250 kbps data rate - Excellent receiver sensitivity (–98 dBm)
- Programmable output power up to +5 dBm
- RF frequency range 2394-2507 MHz
- Suitable for systems targeting compliance with worldwide radio frequency
regulations: ETSI EN 300 328 and EN 300 440 class 2 (Europe),
FCC CFR47 Part 15 (US) and ARIB STD-T66 (Japan)
- IEEE 802.15.4 compliant DSSS baseband
- Microcontroller Support
- Digital RSSI/LQI support
- Automatic clear channel assessment for CSMA/CA
- Automatic CRC
- 768 bytes RAM for flexible buffering and security processing
- Fully supported MAC security
- 4 wire SPI
- 6 configurable IO pins
- Interrupt generator
- Frame filtering and processing engine
- Random number generator
- Development Tools
- Reference design
- IEEE 802.15.4 MAC software
- ZigBee® stack software
- Fully equipped development kit
- Packet sniffer support in hardware
ZigBee® is a registered trademark owned by ZigBee Alliance, Inc.
The CC2520 is TI's second generation ZigBee®/ IEEE 802.15.4 RF transceiver for the 2.4 GHz unlicensed ISM band. This chip enables industrial grade applications by offering state-of-the-art selectivity/co-existence, excellent link budget, operation up to 125°C and low voltage operation.
In addition, the CC2520 provides extensive hardware support for frame handling, data buffering, burst transmissions, data encryption, data authentication, clear channel assessment, link quality indication and frame timing information. These features reduce the load on the host controller.
In a typical system, the CC2520 will be used together with a microcontroller and a few additional passive components.
Technical documentation
No results found. Please clear your search and try again.
View all 15 Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
SMARTRFTRXEBK — SmartRF Transceiver Evaluation Board
The SmartRF Transceiver Evaluation Board (TrxEB) is intended to be used together with Texas Instruments’ low-power RF transceivers for evaluation, performance testing and software development.
The following transceiver evaluation modules are supported:
- CC1101EM*
- CC11xLEM*
- CC112xEM*
- CC1175EM*
- CC1200EM*
- (...)
User guide: PDF
Evaluation board
ALGO-3P-UISP1-TI — Algocraft μISP1 Programmer for Texas Instruments devices
μISP can either work connected to a host PC (RS-232, USB, LAN connections are built-in) or in standalone mode.
The programming cycle execution in standalone mode may occur by simply pressing the START button or through some TTL control lines.
Its compact size and versatility allows a simple (...)
From: Algocraft
Hardware programming tool
ALGO-3P-WRITENOW — Algocraft WriteNow! Programmer
WriteNow! Series of In-System Programmers is a breakthrough in the programming industry. The programmers support a large number of devices (microcontrollers, memories, CPLDs and other programmable devices) from various manufacturers and have a compact size for easy ATE/fixture integration. They (...)
From: Algocraft
Driver or library
Z-STACK-ARCHIVE — Archive for Z-Stack Fully Compliant ZigBee 2012 Solution
NOTE:
This page contains links to obtain previous versions of the Z-Stack releases. For new projects, TI recommends using the newest release in order to take advantages of all improvements and new features. The latest Z-Stack release can be found at www.ti.com/z-stack.
Z-Stack Home
Z-Stack Home is (...)
IDE, configuration, compiler or debugger
CCSTUDIO — Code Composer Studio™ integrated development environment (IDE)
Code Composer Studio is an integrated development environment (IDE) for TI's microcontrollers and processors. It is comprised of a rich suite of tools used to build, debug, analyze and optimize embedded applications. Code Composer Studio is available across Windows®, Linux® and macOS® platforms.
(...)
Supported products & hardware
This design resource supports most products in these categories.
Check the product details page to verify support.
-
parametric-filter Microprocessors & DSPs -
parametric-filter Microcontrollers -
parametric-filter Wi-Fi products -
parametric-filter Low-power 2.4-GHz products -
parametric-filter Signal conditioners -
parametric-filter mmWave radar sensors
Support software
PACKET-SNIFFER — SmartRF™ Packet Sniffer 2.18.1
The SmartRF Packet Sniffer is a PC software application that can display and store radio packets captured by a listening RF device. The capture device is connected to the PC via USB. Various RF protocols are supported. The Packet Sniffer filters and decodes packets and displays them in a convenient (...)
Supported products & hardware
Products
Low-power 2.4-GHz products
- CC2430 — System-on-Chip Solution for 2.4 GHz IEEE 802.15.4 / ZigBee™
- CC2431 — System-on-Chip (SoC) Solution for ZigBee/IEEE 802.15.4 Wireless Sensor Network
- CC2520 — Second generation 2.4 GHz ZigBee/IEEE 802.15.4 wireless transceiver
- CC2530 — Zigbee and IEEE 802.15.4 wireless MCU with 256kB Flash and 8kB RAM
- CC2531 — Zigbee and IEEE 802.15.4 wireless MCU with up to 256kB Flash and 8kB RAM
- CC2533 — A True System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee Applications
- CC2538 — 32-bit Arm Cortex-M3 Zigbee, 6LoWPAN, and IEEE 802.15.4 wireless MCU with 512kB Flash and 32kB RAM
- CC2540 — Bluetooth® Low Energy wireless MCU with USB
- CC2540T — Extended industrial temperature Bluetooth® Low Energy wireless MCU
- CC2541 — Bluetooth® Low Energy and proprietary wireless MCU
- CC2630 — SimpleLink™ 32-bit Arm Cortex-M3 Zigbee and 6LoWPAN wireless MCU with 128kB Flash
- CC2640 — SimpleLink™ 32-bit Arm Cortex-M3 Bluetooth® Low Energy wireless MCU with 128kB Flash
- CC2640R2F — SimpleLink™ 32bit Arm® Cortex®-M3 Bluetooth® Low Energy 5.1 wireless MCU with 128kB flash
- CC2640R2L — SimpleLink™ Bluetooth® 5.1 Low Energy wireless MCU
- CC2650 — SimpleLink™ 32-bit Arm Cortex-M3 multiprotocol 2.4 GHz wireless MCU with 128kB Flash
- CC2650MODA — SimpleLink™ 32-bit Arm Cortex-M3 multiprotocol 2.4 GHz wireless module with 128kB Flash
Sub-1 GHz wireless MCUs
- CC1110-CC1111 — Sub-1 GHz wireless MCU with up to 32 kB Flash memory
- CC1310 — SimpleLink™ 32-bit Arm Cortex-M3 Sub-1 GHz wireless MCU with 128kB Flash
- CC1312R — SimpleLink™ 32-bit Arm Cortex-M4F Sub-1 GHz wireless MCU with 352kB Flash
- CC1314R10 — SimpleLink™ Arm® Cortex®-M33 Sub-1 GHz wireless MCU with 1-MB flash and up to 296 kB of SRAM
- CC1350 — SimpleLink™ 32-bit Arm Cortex-M3 multiprotocol Sub-1 GHz & 2.4 GHz wireless MCU with 128kB Flash
- CC1352P — SimpleLink™ Arm Cortex-M4F multiprotocol Sub-1 GHz & 2.4 GHz wireless MCU integrated power amplifier
- CC1352R — SimpleLink™ Arm Cortex-M4F multiband Sub-1GHz & 2.4GHz wireless MCU with EdgeAI support
Sub-1 GHz transceivers
- CC1101 — Low-power Sub-1 GHz wireless transceiver
- CC110L — Value line Sub-1 GHz wireless transceiver
- CC1120 — High performance Sub-1 GHz wireless transceiver for narrowband systems
- CC1125 — Ultra-high performance Sub-1 GHz wireless transceiver for narrowband systems
Other wireless products
- CC2420 — Single-Chip 2.4 GHz IEEE 802.15.4 Compliant and ZigBee™ Ready RF Transceiver
- CC2500 — Low Cost, Low-Power 2.4 GHz RF Transceiver Designed for Low-Power Wireless Apps in the 2.4 GHz ISM B
- CC2510 — 2.4 GHz Radio Transceiver, 8051 MCU, and 16KB or 32 KB Memory
- CC2510F8 — 2.4 GHz Radio Transceiver, 8051 MCU and 8 kB Flash memory
- CC2511 — 2.4 GHz Radio Transceiver, 8051 MCU, 16KB or 32KB Flash memory and full-speed USB interface
- CC2511F8 — 2.4 GHz Radio Transceiver, 8051 MCU, 8 kB Flash memory and full-speed USB interface
- CC2530-RF4CE — Zigbee, IEEE 802.15.4 and RF4CE wireless MCU with 256kB Flash and 8kB RAM
- CC2531-RF4CE — Zigbee, IEEE 802.15.4 and RF4CE wireless MCU with up to 256kB Flash and 8kB RAM
- CC2620 — SimpleLink™ 32-bit Arm Cortex-M3 Zigbee® RF4CE wireless MCU with 128kB Flash
Automotive wireless connectivity products
- CC2541-Q1 — Automotive qualified SimpleLink Bluetooth® Low Energy wireless MCU
- CC2640R2F-Q1 — SimpleLink™ automotive qualified 32-bit Arm Cortex-M3 Bluetooth® Low Energy wireless MCU
Hardware development
Evaluation board
- LAUNCHXL-CC1310 — CC1310 LaunchPad™ development kit for sub-1-GHz SimpleLink™ wireless MCU
- LAUNCHXL-CC1352P — CC1352P LaunchPad™ development kit for SimpleLink™ multi-band wireless MCU
Development kit
- LAUNCHXL-CC1312R1 — CC1312R LaunchPad™ development kit for sub-1-GHz SimpleLink™ wireless MCU
- LAUNCHXL-CC1350 — CC1350 LaunchPad™ development kit for SimpleLink™ dual-band wireless MCU
Software
Software programming tool
- FLASH-PROGRAMMER — SmartRF Flash Programmer
Calculation tool
- PACKET-SNIFFER — SmartRF Protocol Packet Sniffer
- SMARTRFTM-STUDIO — SmartRF Studio
Driver or library
- BLE-STACK — Bluetooth Low Energy software stack
- REMOTI — RF4CE Compliant Protocol Stack
- SIMPLICITI — SimpliciTI Compliant Protocol Stack
- TI-15.4-STACK-GATEWAY-LINUX-SDK — TI 15.4-Stack Gateway Linux Software Development Kit
- TIMAC — IEEE802.15.4 Medium Access control (MAC) software stack
- Z-STACK — A fully compliant ZigBee 3.x solution: Z-Stack
Calculation tool
SMARTRF-STUDIO-7 — SmartRF Studio 7 application software
SmartRF™ Studio is a Windows application that helps designers of RF systems to easily evaluate the radio at an early stage in the design process for all TI CC1xxx and CC2xxx low-power RF devices. It simplifies generation of the configuration register values and commands, as well as practical (...)
Supported products & hardware
Products
MSP430 microcontrollers
- CC430F6127 — 20 MHz MCU with 32KB Flash, 4KB SRAM, Sub-1 GHz radio, AES-128, I2C/SPI/UART, 96 seg LCD
- CC430F6135 — 20 MHz MCU with 16KB Flash, 2KB SRAM, Sub-1 GHz radio, AES-128, 12-bit ADC, I2C/SPI/UART, 96 seg
- CC430F6147 — 20 MHz MCU with 32KB Flash, 4KB SRAM, Sub-1 GHz radio, AES-128, 10-bit ADC, I2C/SPI/UART, 96 seg
Low-power 2.4-GHz products
- CC2430 — System-on-Chip Solution for 2.4 GHz IEEE 802.15.4 / ZigBee™
- CC2431 — System-on-Chip (SoC) Solution for ZigBee/IEEE 802.15.4 Wireless Sensor Network
- CC2520 — Second generation 2.4 GHz ZigBee/IEEE 802.15.4 wireless transceiver
- CC2530 — Zigbee and IEEE 802.15.4 wireless MCU with 256kB Flash and 8kB RAM
- CC2531 — Zigbee and IEEE 802.15.4 wireless MCU with up to 256kB Flash and 8kB RAM
- CC2533 — A True System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee Applications
- CC2538 — 32-bit Arm Cortex-M3 Zigbee, 6LoWPAN, and IEEE 802.15.4 wireless MCU with 512kB Flash and 32kB RAM
- CC2540 — Bluetooth® Low Energy wireless MCU with USB
- CC2540T — Extended industrial temperature Bluetooth® Low Energy wireless MCU
- CC2541 — Bluetooth® Low Energy and proprietary wireless MCU
- CC2630 — SimpleLink™ 32-bit Arm Cortex-M3 Zigbee and 6LoWPAN wireless MCU with 128kB Flash
- CC2640 — SimpleLink™ 32-bit Arm Cortex-M3 Bluetooth® Low Energy wireless MCU with 128kB Flash
- CC2640R2F — SimpleLink™ 32bit Arm® Cortex®-M3 Bluetooth® Low Energy 5.1 wireless MCU with 128kB flash
- CC2640R2L — SimpleLink™ Bluetooth® 5.1 Low Energy wireless MCU
- CC2642R — SimpleLink™ 32-bit Arm Cortex-M4F Bluetooth® Low Energy wireless MCU with 352kB Flash
- CC2650 — SimpleLink™ 32-bit Arm Cortex-M3 multiprotocol 2.4 GHz wireless MCU with 128kB Flash
- CC2650MODA — SimpleLink™ 32-bit Arm Cortex-M3 multiprotocol 2.4 GHz wireless module with 128kB Flash
- CC2651P3 — SimpleLink™ 32-bit Arm® Cortex®-M4 single-protocol 2.4 GHz wireless MCU with 352-kB Flash
- CC2651R3 — SimpleLink™ 32-bit Arm® Cortex®-M4 single-protocol 2.4-GHz wireless MCU with 352-kB flash
- CC2652P — SimpleLink™ Arm Cortex-M4F multiprotocol 2.4 GHz wireless MCU with integrated power amplifier
- CC2652P7 — SimpleLink™ Arm® Cortex®-M4F multiprotocol 2.4-GHz wireless MCU, 704-kB Flash, integrated power amp
- CC2652PSIP — SimpleLink™ multiprotocol 2.4-GHz wireless system-in-package module with integrated power amplifier
- CC2652R — SimpleLink™ 32-bit Arm Cortex-M4F multiprotocol 2.4 GHz wireless MCU with 352kB Flash
- CC2652R7 — SimpleLink™ Arm® Cortex®-M4F multiprotocol 2.4-GHz wireless MCU with 704-kB Flash
- CC2652RB — SimpleLink™ 32-bit Arm Cortex-M4F multiprotocol 2.4 GHz wireless MCU with crystal-less BAW resonator
- CC2652RSIP — SimpleLink™ multiprotocol 2.4-GHz wireless system-in-package module with 352-KB memory
- CC2674P10 — SimpleLink™ Arm® Cortex®-M33 multiprotocol 2.4GHz wireless MCU with 1MB flash and power amplifier
- CC2674R10 — SimpleLink™ Arm® Cortex®-M33 multiprotocol 2.4-GHz wireless MCU with 1-MB flash
Sub-1 GHz wireless MCUs
- CC1110-CC1111 — Sub-1 GHz wireless MCU with up to 32 kB Flash memory
- CC1310 — SimpleLink™ 32-bit Arm Cortex-M3 Sub-1 GHz wireless MCU with 128kB Flash
- CC1311P3 — SimpleLink™ Arm® Cortex®-M4 Sub-1GHz wireless MCU with 352KB flash and integrated +20dBm power amp
- CC1311R3 — SimpleLink™ Arm® Cortex®-M4 Sub-1 GHz wireless MCU with 352-kB flash
- CC1312PSIP — Sub-1 GHz system-in-package (SiP) module with integrated power amplifier
- CC1312R — SimpleLink™ 32-bit Arm Cortex-M4F Sub-1 GHz wireless MCU with 352kB Flash
- CC1312R7 — SimpleLink™ Arm® Cortex®-M4F multiprotocol Sub-1 GHz wireless MCU with 704-kB Flash
- CC1314R10 — SimpleLink™ Arm® Cortex®-M33 Sub-1 GHz wireless MCU with 1-MB flash and up to 296 kB of SRAM
- CC1350 — SimpleLink™ 32-bit Arm Cortex-M3 multiprotocol Sub-1 GHz & 2.4 GHz wireless MCU with 128kB Flash
- CC1352P — SimpleLink™ Arm Cortex-M4F multiprotocol Sub-1 GHz & 2.4 GHz wireless MCU integrated power amplifier
- CC1352P7 — SimpleLink™ Arm® Cortex®-M4F multiband sub-1GHz & 2.4GHz wireless MCU with EdgeAI support, +20dBm
- CC1352R — SimpleLink™ Arm Cortex-M4F multiband Sub-1GHz & 2.4GHz wireless MCU with EdgeAI support
- CC1354P10 — SimpleLink™ Arm® Cortex®-M33 multiband wireless MCU with EdgeAI support, 1MB + 296KB, +20dBm
- CC1354R10 — SimpleLink™ Arm® Cortex®-M33 multiband wireless MCU with EdgeAI support, 1MB flash, 296KB SRAM
- CC430F5123 — 16-bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 8kB Flash and 2kB RAM
- CC430F5125 — 16-Bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 16kB Flash and 2kB RAM
- CC430F5133 — 16-Bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 12-Bit ADC, 8kB Flash and 2kB RAM
- CC430F5137 — 16-Bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 12-Bit ADC, 32kB Flash and 4kB RAM
- CC430F5143 — 16-Bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 10-bit ADC, 8kB Flash and 2kB RAM
- CC430F5145 — 16-Bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 10-bit ADC, 16kB Flash and 2kB RAM
- CC430F5147 — 16-Bit ultra-low-power CC430 Sub 1 GHz wireless MCU with 10-bit ADC, 32kB Flash and 4kB RAM
Sub-1 GHz transceivers
- CC1020 — Single-chip FSK/OOK CMOS wireless transceiver for Narrowband apps in 402-470 and 804-940 MHz range
- CC1021 — Multichannel FSK/OOK CMOS wireless transceiver for Narrowband app w/Ch Spacings of 50 kHz or Higher
- CC1070 — Single-chip, Low-Power, Low-Cost CMOS FSK/GFSK/ASK/00K RF Transmitter for Narrowband & Multi-Ch apps
- CC1100 — Highly Integrated MultiCh RF transceiver Designed for Low-Power Wireless apps
- CC1100E — Low-power Sub-1GHz wireless transceiver for China and Japan frequency bands
- CC1101 — Low-power Sub-1 GHz wireless transceiver
- CC110L — Value line Sub-1 GHz wireless transceiver
- CC1120 — High performance Sub-1 GHz wireless transceiver for narrowband systems
- CC1121 — High performance low power Sub-1 GHz wireless transceiver
- CC1125 — Ultra-high performance Sub-1 GHz wireless transceiver for narrowband systems
- CC113L — Value line Sub-1 GHz wireless receiver
- CC1150 — Highly integrated multichannel wireless transmitter designed for low-power wireless applications
- CC115L — Value line Sub-1 GHz wireless transmitter
- CC1175 — High performance wireless transmitter for narrowband systems
- CC1200 — Low power and high performance wireless transceiver
- CC1201 — Low power and high performance wireless transceiver
Other wireless products
- CC2420 — Single-Chip 2.4 GHz IEEE 802.15.4 Compliant and ZigBee™ Ready RF Transceiver
- CC2500 — Low Cost, Low-Power 2.4 GHz RF Transceiver Designed for Low-Power Wireless Apps in the 2.4 GHz ISM B
- CC2510 — 2.4 GHz Radio Transceiver, 8051 MCU, and 16KB or 32 KB Memory
- CC2510F8 — 2.4 GHz Radio Transceiver, 8051 MCU and 8 kB Flash memory
- CC2511 — 2.4 GHz Radio Transceiver, 8051 MCU, 16KB or 32KB Flash memory and full-speed USB interface
- CC2511F8 — 2.4 GHz Radio Transceiver, 8051 MCU, 8 kB Flash memory and full-speed USB interface
- CC2530-RF4CE — Zigbee, IEEE 802.15.4 and RF4CE wireless MCU with 256kB Flash and 8kB RAM
- CC2531-RF4CE — Zigbee, IEEE 802.15.4 and RF4CE wireless MCU with up to 256kB Flash and 8kB RAM
- CC2543 — 2.4 GHz RF Value Line SoC with 32kB flash, 16 GPIO, I2C, SPI and UART
- CC2544 — 2.4 GHz RF Value Line SoC with 32kB flash, USB, SPI and UART
- CC2545 — 2.4 GHz RF Value Line SoC with 32kB flash, 31 GPIO, I2C, SPI and UART
- CC2550 — Low Cost 2.4 GHz Transmitter Designed for Low-Power Wireless Applications in 2.4 GHz ISM Band
- CC2620 — SimpleLink™ 32-bit Arm Cortex-M3 Zigbee® RF4CE wireless MCU with 128kB Flash
Automotive wireless connectivity products
- CC2541-Q1 — Automotive qualified SimpleLink Bluetooth® Low Energy wireless MCU
- CC2640R2F-Q1 — SimpleLink™ automotive qualified 32-bit Arm Cortex-M3 Bluetooth® Low Energy wireless MCU
- CC2642R-Q1 — Automotive qualified SimpleLink™ Bluetooth® Low Energy wireless MCU
- CC2662R-Q1 — Automotive qualified SimpleLink™ wireless MCU for use in wireless battery management systems
Hardware development
Development kit
- CC1125DK — CC1125 Development Kit
- CC1200DK — CC1200 Development Kit
- CC1350STK — Simplelink CC1350 SensorTag Bluetooth and Sub-1GHz Long Range Wireless Development Kit
- CC2541DK-MINI — CC2541 Mini Development Kit
- CC2650STK — SimpleLink™ Bluetooth low energy/Multi-standard SensorTag
- LAUNCHXL-CC1312R1 — CC1312R LaunchPad™ development kit for sub-1-GHz SimpleLink™ wireless MCU
- LAUNCHXL-CC1350 — CC1350 LaunchPad™ development kit for SimpleLink™ dual-band wireless MCU
- LAUNCHXL-CC1352R1 — CC1352R LaunchPad™ development kit for SimpleLink™ multi-band wireless MCU
- LAUNCHXL-CC2650 — SimpleLink™ CC2650 wireless MCU LaunchPad™ Development Kit
- LP-CC1311P3 — CC1311P3 LaunchPad™ development kit for SimpleLink™ sub-1-GHz wireless MCU
- LP-CC1312R7 — CC1312R7 LaunchPad™ development kit for SimpleLink™ multi-standard wireless MCU
- LP-CC2652RB — CC2652RB LaunchPad™ development kit for BAW multi-protocol 2.4-GHz SimpleLink™ wireless MCU
- LP-EM-CC1314R10 — CC1314R10 LaunchPad™ development kit for SimpleLink™ Sub-1 GHz wireless MCU
- LP-EM-CC1354P10 — CC1354P10 LaunchPad™ development kit for SimpleLink™ Sub-1 GHz and 2.4GHz wireless microcontroller
Evaluation board
- BOOSTXL-CC1120-90 — BoosterPack for Applications from 902MHz to 928MHz
- BOOSTXL-CC1125 — CC1125 BoosterPack for 868/915 MHz Applications
- LAUNCHXL-CC1310 — CC1310 LaunchPad™ development kit for sub-1-GHz SimpleLink™ wireless MCU
- LAUNCHXL-CC2640R2 — CC2640R2 LaunchPad™ development kit for SimpleLink™ Bluetooth® Low Energy wireless MCU
- LAUNCHXL-CC26X2R1 — CC26x2R LaunchPad™ development kit for multi-standard SimpleLink™ wireless MCU
- LP-CC1352P7 — CC1352P7 LaunchPad™ development kit for SimpleLink™ multi-band wireless MCU
- LP-CC2651P3 — CC2651P3 LaunchPad™ development kit for SimpleLink™ multi-standard wireless MCU
- LP-CC2652PSIP — CC2562PSIP LaunchPad™ development kit for SimpleLink™ multiprotocol 2.4-GHz wireless SIP module
- LP-CC2652R7 — CC2652R7 LaunchPad™ development kit for SimpleLink™ multi-standard wireless MCU
- LP-CC2652RSIP — CC2652RSIP LaunchPad™ development kit for SimpleLink™ multi-protocol wireless MCU
- SMARTRF06EBK — SmartRF06 Evaluation Board
- SMARTRFTRXEBK — SmartRF Transceiver Evaluation Board
- LP-CC2651R3SIPA — CC2651R3SIPA LaunchPad™ development kit for SimpleLink™ multiprotocol 2.4-GHz wireless SIP module
Interface adapter
- BOOST-CCEMADAPTER — EM Adapter BoosterPack
Daughter card
- CC1120EMK-169 — CC1120 Evaluation Module Kit 169MHz
- CC1120EMK-420-470 — CC1120 Evaluation Module Kit 420-470MHz
- CC1120EMK-868-915 — CC1120 Evaluation Module Kit 868-915MHz
- CC1121EMK-868-915 — CC1121 Evaluation Module Kit 868-915MHz
- CC1175EMK-868-915 — CC1175 Evaluation Module Kit 868-915MHz
- CC1200EMK-420-470 — CC1200 Evaluation Module Kit 420-470 MHz
- CC1200EMK-868-930 — CC1200 Evaluation Module Kit 868-930 MHz
- CC1201EMK-868-930 — CC1201 Evaluation Module Kit 868-930 MHz
- CC2530EMK — CC2530 Evaluation Module Kit
- CC2531EMK — CC2531 USB Evaluation Module Kit
- CC2538-CC2592EMK — CC2538-CC2592 Evaluation Module Kit
- CC2538EMK — CC2538 Evaluation Module Kit
- CC2540EMK-USB — Bluetooth Low Energy and proprietary wireless MCU
Design tool
SIMPLELINK-2-4GHZ-DESIGN-REVIEWS — Hardware design reviews for SimpleLink™ CC2xxx devices
The SimpleLink hardware design review process provides a way to get in touch, one-on-one, with a subject matter expert that can help review your design and provide valuable feedback. A simple three-step process for requesting a review as well as links to relevant technical documentation and (...)
Reference designs
CC2592EMK-RD — Standalone 2.4GHz Range Extender Reference Design
This standalone 2.4 GHz range extender reference design provides all the information needed to use the SimpleLink™ CC2592 range extender (PA/LNA front end) with any 2.4 GHz RF radio in a wide range of applications, including sensor mesh networks and gateways. The CC2592 range extender contains PA, (...)
Reference designs
TIDM-RF-SENSORNODE — RF Sensor Node Development Platform for 6LoWPAN and 2.4 GHz Applications
The RF Sensor Node Platform is intended as a miniature development platform for 6LoWPAN and 2.4 GHz applications. The platform has three on-board sensors which includes a 3-axis accelerometer, a temperature sensor and two light sensors. The RF Sensor Node Platform can be a stand-alone sensor node (...)
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| VQFN (RHD) | 28 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.